Businesses: if you are interested in a personalized quote, please




Frequently Asked Questions

Why use VTE Inc. battery terminal insulators? View
Uncovered, ungrounded and live battery terminals create an electrical hazard. According to CFR 183.420 (b) batteries must be installed so that metallic objects can't come into contact with the ungrounded battery terminals. This is a law.






VTE, Inc., offers a safe and inexpensive solution to keep your company in compliance with this law. When installed properly, our caps provide protection from electrical hazards.

Conductive vs. Fastening Nuts View

Conductive Fasteners (nuts)

Brass or plated brass nuts are used when a fastener is to be used in a conductive position. These conductive fasteners pass current more efficiently than steel. These nuts will be indicated by a 'BLUE DOT' marking, and should be kept in their conductive location.

Tightening Fasteners (nuts)

Stainless steel and steel nuts are used to torque or tighten an assembly. These fasteners are in a position where torque is necessary, but not conductivity. These fasteners are less expensive, thereby lowering the cost of the assembly, while increasing the amount of fastening torque allowed.

What are my material options? View
Properties
Material UL94 Flame Class Brittleness Temp oC Service Temp oC Tensile Strength, PSI Elongation, % Tear Strength, PPI
V - Vinyl
(Standard, Self Extinguishing)
V-2 -48 105 1550 400 230
F - Vinyl
(FR Material, Non-Flammable)
V-0 -30 105 1500 350 230
T - TPR *
(Thermoplastic Rubber)
HB <-60 125 1020 450 131

S Material has been discontinued.

* Due to difficulties in molding with T material, not all insulators are available in this material. Please contact VTE Inc. for functional usefulness and availability.

Click Here to see comprehensive material properties.

Define the term 'Barrel' View

Barrel: part of the insulator cap designed to cover the terminal length of the entering cable or wire.

Where do I get the measurement for the cap's diameter? View

The diameter of the portion of the cap that fits over the terminal and post.

The inside diameter of the cap's body should match the outer diameter of the terminal and post.

What does the phrase 'Cable Entry Size' mean? View

Cable Entry Size: Where the cable enters the cap.

To size, use the inner diameter of the entrance of the cap's barrel.

How to determine right or left side cable entry View

1) Position insulator so terminal opening is facing down.

2) Position insulator so cable entry is near you.

3) Cable opening determines cable entry side.

What is a ring or eyelet terminal? View

Ring Terminals often are brazed, with open end.

Lug terminals often are closed end, drawn from copper tube.

Both ring and lug terminals are considered eyelet terminals.

What is the post height? View

Post Height: the height of the stud / post / screw that must be covered.

Use the body of the cap's height for measurement.

How to find terminal length? View

Find the terminal length by measuring from the center of the terminal ring and the end of the exposed metal.

Use this measurement to determine the cap's barrel length.

What is the term 'Terminal O.D.' refer to? View

Terminal O.D. (outside diameter) refers to the width of the terminal or eyelet ring.

Use this measurement to determine a cap's body diameter.

Do VTE Insulators have a shelf life? View

When stored in accordance with normal warehouse conditions, the shelf life of our molded components can exceed 10 years without failure.




 
USA Factory / Headquarters European Headquarters Other Regions
VTE Inc.
5437 Robinson Rd
Pellston Mi 49769
United States
PH: 1.231.539.8000
FX: 1.231.344.5914
Email: info@vteworld.com
www.vteworld.com
VTE Europe BV
Trapgans 8 J
Ankeveen 1244RL
Netherlands
PH: 035-6565560
FX:
Email: info@vte.nl
www.vte.nl

Please contact VTE USA or
VTE Europe for ordering information.

VTE is looking for dealers
and distributors in new
areas. Please contact us
for information.

HOME » F. A. Q.
jazz日本少妇免费视频_日本最新免费二区三区_日本大片免a费观看视频无码